Snap-on Motorized Loader Manual de usuario Pagina 29
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-2
Setup and Programming
Setting Up the Motorized Control Loader System
1. Position the roll cabinet on a level floor and lock the
wheels.
2. Mount the indicator stand, part number 2000-111-0, to
the Loader.
3. Mount the 2000-810-01 Indicator to the stand.
4. Connect the cables between the Indicator, Motorized
Control Box and Power Amplifier Box.
(Refer to chapter 6)
5. Install the appropriate MULTITEST transducer to the
Loader drive.
6. Install two (2) quick release pins, part number 2000-195-
12.
7. Connect the transducer cable, part number 2000-900-
120, between the Indicator and transducer.
8. Select the appropriate AC voltage input at the rear of the
Indicator. Connect the AC power cables to the Indicator
and the Power Amplifer Box. For additional information
refer to Chapter 6—Loader Rear Panel Controls.
9. Install the safety shield to the front of the Loader.
10. Install the reaction pins into the reaction slide on the
Loader.
For testing procedures refer to Chapter 4—Using
the Torque Tester.
Various fixtures, cables and adaptors are available for testing
the most common compression or tension gauges. Ask your
CDI sales representative for assistance.
- MOTORIZED CONTROL LOADER 1
- USER'S MANUAL 1
- Torque-Angle Tutorial 2
- Front Panel Function Keys 3
- Table of Contents 4
- Table of Illustrations 6
- Using this Manual 7
- Using This Manual 8
- Safety Messages 8
- Safety Information 10
- LIMITING SWITCHES 12
- Introduction 13
- Functional Description and 15
- Specifications 15
- 2000-810-01 Indicator 17
- Front Panel 17
- F — Maximum Range Display 18
- Rear Panel (Input/Output) 21
- D — PRINTER PORT (DB-9P) 22
- E — OPTIONAL (DB-9P) 22
- F — TRANSDUCER INPUT (DB-37S) 22
- G — VOLTAGE SELECT 22
- Torque/Force Transducers 27
- Setup and 28
- Programming 28
- Setup and Programming 29
- Powering the Equipment 31
- 4-in-1 Transducer Select 31
- Programming Setup 32
- Programming AUTO CLEAR 34
- DATA LIST Memory 36
- Clear Single Memory Location 37
- Setting Up Printer/PC Ports 38
- Selecting Printer/PC Ports 38
- Encoders 40
- Set Up Torque-Angle Algorithm 42
- Using the Multitest 45
- Torque Calibration System 45
- Testing Power Tools 49
- Figure 4-3: Value Display 53
- Printing Statistical Analysis 54
- Displaying Data List on LCD 55
- Measuring Torque and Angle 58
- Angle Only 59
- Torque-Angle Algorithm 60
- Calibration 61
- Mounting Details 62
- Quick Check 65
- Torque/Force Calibrations 68
- Gravitational Effects 71
- Correction Factor for Weights 72
- 2000-800-02 Motorized Loader 73
- Functional Description 74
- Torque Tester/Calibrator 75
- A — Drive Adaptor 76
- B — Transducer (Accessory) 76
- C — Transducer Mounting 76
- Ball Handle Adaptor 78
- 4-in-1 Transducer (Accessory) 79
- Extension Arm (Accessory) 80
- Motorized Control Box 81
- Cable connections: 83
- Click Mode: 85
- F1 key to select Dial Mode 88
- RUN key to start Dial Mode: 88
- Example : 88
- NOTE : 88
- MANUAL MODE 93
- Types of Loader Testing 94
- Force Testing 95
- Appendix 97
- Accessories 100
- Calibration Accessories 101
Relacionado con productos y manuales para Herramientas Snap-on Motorized Loader
Herramientas Snap-on DTT Manual de usuario
(24 paginas)
(24 paginas)
Antec 4U manuales
Manuales del propietario y guías del usuario para Accesorios De Computador Antec 4U.
Ofrecemos 1 manuales en pdf Antec 4U para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales